How Much Decomposed Granite for a Path?

Updated 2026-10-30 · Yardly

Background and Pain Points

Decomposed granite—DG for short—is one of the most forgiving materials you can put on a garden path. It drains well, packs down firm, looks natural against planting beds, and costs far less than pavers or flagstone. The trouble almost always starts before the first wheelbarrow arrives: figuring out how much to buy.

Most homeowners run into the same set of problems.

The bag-to-bulk gap. A 40-pound bag from the big-box store covers roughly 4 to 5 square feet at 2 inches deep. A 100-foot path that’s 3 feet wide needs about 300 square feet—so you’d be buying 60-plus bags. Bulk is almost always cheaper, but bulk is sold in cubic yards or tons, not square feet, and that conversion is where people get stuck.

Depth confusion. Everyone quotes a different number. Two inches, three inches, four inches. The right answer depends on whether feet or vehicles use the path and whether you’re stabilizing the surface.

Compaction loss. Loose DG fluffs up. Once you water and compact it, the same volume settles into a thinner layer, so a straight area calculation leaves you short.

Stabilized versus loose. A binder turns DG into something closer to a solid surface, but it changes both the quantity you need and the way you install it. Many people buy stabilized DG without realizing it has to be mixed, wetted, and rolled within a specific window.

The good news: the math is simple once you know the three numbers that matter—area, depth, and bulk density.

Why It Matters (Core Value)

Getting the quantity right saves money in both directions. Order short and you’ll pay a second delivery fee, which can easily exceed the cost of the material itself—plus you risk a visible color or grade mismatch between loads. Order heavy and you’re stuck with a pile of gravel on the driveway and a disposal problem.

Depth matters just as much as total volume. A path that’s too shallow will rut, migrate into the surrounding soil, and expose bare spots after one wet season. A path that’s too deep wastes material and can sit soft and spongy because the DG never knits together under compaction.

Finally, the stabilization decision should drive the number, not the other way around. Stabilized DG is normally installed at a consistent 2 to 2½ inches because the binder is doing the structural work; loose DG often needs 3 to 4 inches because the aggregate alone has to carry the load. Choosing after you’ve ordered is the most expensive mistake in the process.

How to Do It Right (Step-by-Step)

Step 1: Measure the actual footprint

Measure the centerline length of the path in feet, following the curves, then multiply by the average width. For a winding path, break it into straight and curved segments and add them up. A curved path with a 5-foot width and a 70-foot centerline is still 350 square feet—curves cost you length, not area.

Subtract any sections that won’t get DG, such as a stepping-stone landing or a paved apron at the door.

Step 2: Pick your depth

  • 2 inches: light foot traffic over a well-compacted, stable subgrade, especially stabilized DG.
  • 3 inches: the standard for loose DG walkways in most residential yards.
  • 4 inches: heavier use, soft or clay subgrade, or where the DG is the only structural layer.
  • 4 inches of compacted base plus 2 inches of DG: the right build for a path that will see wheelbarrows, mowers, or occasional vehicles.

Step 3: Convert area to volume

Multiply square feet by depth in feet, then divide by 27 to get cubic yards.

Example: 70 feet long × 5 feet wide = 350 square feet. At 3 inches (0.25 feet): 350 × 0.25 = 87.5 cubic feet. 87.5 ÷ 27 = 3.24 cubic yards.

Step 4: Convert to tons and add a cushion

DG weighs roughly 1.35 to 1.5 tons per cubic yard depending on moisture and gradation. Using 1.4 as a working figure: 3.24 × 1.4 = 4.5 tons. Add 10 to 15 percent for compaction and settling, which brings it to about 5 tons, or roughly 5½ tons if the subgrade is uneven.

A shortcut that works for most projects: one ton covers about 80 to 100 square feet at 2 to 3 inches deep. For our 350-square-foot path at 3 inches, that’s 3.5 to 4.4 tons before the cushion—consistent with the math above.

Step 5: Decide on stabilization early

Loose DG is simply spread, watered, and compacted. It’s cheaper, easy to top-dress, and fine for low-traffic garden paths, but it will scatter, develop potholes on slopes, and need occasional raking.

Stabilized DG blends the aggregate with a binder—typically an organic resin, polymer, or lignosulfonate—before compaction. The result is firmer, resists displacement and weed growth, and holds up on slopes up to roughly 20 percent. Expect to pay noticeably more per ton, and expect the installer (or you) to mix the binder thoroughly, bring the material to the correct moisture, compact it in lifts, and keep traffic off for 24 to 72 hours. Binder applied as a spray-on topcoat over loose DG is not the same thing and rarely performs well.

Order stabilized DG pre-blended from the supplier if you can. Field mixing is doable but inconsistent, and uneven binder distribution shows up as soft patches a season later.

Step 6: Prepare, edge, and compact

Excavate to your finish depth plus about an inch so the DG sits flush with grade or slightly below adjacent turf. Compact the subgrade, install rigid edging on both sides—DG has no internal strength at the edges and will spread without restraint—and lay a woven geotextile if the soil is clay-heavy or weed-prone. Spread the DG in 2-inch lifts, water lightly, and compact each lift with a plate compactor. For stabilized material, follow the supplier’s moisture and cure instructions exactly.

Common Mistakes and How to Avoid Them

Calculating from bag coverage. Bag labels list thin-spread coverage. Always compute from cubic volume and bulk density instead.

Forgetting compaction loss. Loose DG settles 10 to 15 percent. Build that into the order rather than making a second trip.

Skipping edge restraint. This is the single most common cause of a DG path turning into a scattered strip within two years. Steel, aluminum, or heavy timber edging on both sides is not optional.

Using 2 inches of loose DG under foot traffic. It looks fine for a month, then ruts. Go to 3 inches unless the material is stabilized over a solid base.

Overwatering stabilized DG. Too much water before compaction pushes the binder to the surface and leaves a crusty, fragile top. Mix to the specified moisture, not to “looks wet.”

Ignoring drainage and slope. DG is permeable, but water still has to go somewhere. On grades steeper than about 20 percent, use stabilization or add shallow grade breaks.

Ordering from two different batches. DG color varies by quarry and lot. Buy the full quantity at once, or confirm the supplier is pulling from the same stockpile.

Summary and Next Steps

The quantity question comes down to three steps: measure the footprint in square feet, multiply by depth in feet, divide by 27 for cubic yards, then multiply by about 1.4 for tons. Add 10 to 15 percent for compaction, and use the rule of thumb that one ton covers roughly 80 to 100 square feet at 2 to 3 inches.

Then decide on the surface type. Loose DG at 3 inches suits light foot traffic and tight budgets. Stabilized DG at 2 to 2½ inches over a compacted base costs more up front but holds its shape, resists weeds, and handles slopes—provided it’s mixed and cured correctly.

Before you order, walk the path one more time with a tape measure and a sketch. Mark the depth you want on the plan, confirm the edging will be on site before the material arrives, and call two local suppliers for bulk pricing and delivery minimums. With those numbers in hand, the rest of the build is straightforward labor.

Advertisement