How Much Gravel for a Shed Base?

Updated 2026-11-20 · Yardly

Background and Pain Points

Almost every shed that heaves, sags, or rots out within a few years traces the problem back to the same spot: the ground underneath it. Wood needs to stay dry, and the soil beneath a shed needs to drain and stay put through freeze-thaw cycles, spring mud, and summer drought. Gravel solves both problems at once — it drains freely, it compacts into a firm, stable platform, and it keeps wood out of standing water — which is why a crushed-stone pad is the default choice for everything from a 6x8 garden tool shed to a 12x20 workshop.

The trouble starts when people try to buy the material. Gravel is sold by the cubic yard or by the ton, and “a yard” of stone looks nothing like a yard of mulch once it’s spread and compacted. Order too little and you’re making a second trip with a half-built pad sitting open in the rain. Order too much and you’re staring at a two-ton pile in the driveway with nowhere to put it. Add in the question of depth — 2 inches? 4? 6? — and the fact that a shed doesn’t load its base evenly, and the whole thing becomes guesswork.

Then there’s the other half of the problem: a lot of sheds don’t sit on a full gravel pad at all. Smaller units, and any shed built on a timber-frame skid foundation, only need gravel under the contact points. Getting that distinction wrong means either way too much stone or a base that fails under the first heavy snow load.

This guide gives you the numbers first, then the method, so you can order once and build it right.

Why It Matters (Core Value)

The right amount of gravel and the right depth buy you four things:

  • Drainage. Crushed stone moves water away from the shed floor and skids. A shed sitting on bare soil or a solid concrete slab in a low spot wicks moisture into the bottom plate and rots it.
  • Load distribution. A shed’s weight concentrates at its corners and along its rim. Four to six inches of compacted crushed stone spreads that load over a wider area so the structure doesn’t sink unevenly.
  • Frost and movement resistance. A properly compacted, well-drained stone base drains water that would otherwise freeze and heave. (In cold climates, check local frost-depth guidance for anything permanent.)
  • A flat, true starting point. It’s far easier to level a pad of compacted gravel than to shim a shed sitting on dirt.

Getting the quantity right matters because gravel is heavy and awkward to handle twice. A single cubic yard of crushed stone weighs roughly 1.35 to 1.4 tons. For an 8x10 shed at 4 inches deep, you’re already looking at well over a ton of material. Accuracy saves money, trips, and your back.

How to Do It Right (Step-by-Step)

Step 1: Measure the footprint — then add overhang

Measure your shed’s footprint, then extend it 6 to 12 inches beyond the shed on every side. The extra apron supports the rim, keeps splashback off the siding, and gives you room to work. A 10x12 shed with a 6-inch apron becomes an 11x13 pad.

Step 2: Pick your depth

  • 4 inches compacted — the minimum for any shed, and fine for units up to about 8x10 sitting on well-drained, sandy or gravelly soil.
  • 6 inches compacted — the safer choice for sheds larger than 8x10, for clay or poorly draining soil, and for anything holding heavy equipment.

Step 3: Run the numbers

Use this formula:

Length (ft) × Width (ft) × Depth (ft) ÷ 27 = cubic yards

Then add 15–20% for compaction and spillage. To convert to tons, multiply cubic yards by about 1.4.

Here are ready-made figures that already include 20% overage:

Shed footprintPad size (6” apron)4” deep6” deep
8x89x91.0 cu yd (1.4 tons)1.5 cu yd (2.1 tons)
8x109x111.2 cu yd (1.7 tons)1.8 cu yd (2.5 tons)
10x1011x111.5 cu yd (2.1 tons)2.3 cu yd (3.2 tons)
10x1211x131.8 cu yd (2.5 tons)2.7 cu yd (3.8 tons)
12x1613x172.9 cu yd (4.0 tons)4.3 cu yd (6.0 tons)

Step 4: Choose the right stone

Buy #57 crushed stone (roughly 3/4-inch angular rock) or a crushed stone with fines (often sold as crusher run or grade

Advertisement